Broken Cyberster logo

[cyberthai]

My Cyberster logo broke during car wash by hand. I can not blame anyone else than myself.
So be very carefull or get you car washed by someone else. It is easier to blame!!

 

[salty]

Take the rest off, looks better.

 

[4Rens]

In an earlier treat this topic has already been discussed. I think I will remove the logo on delivery and replace it with these two letters. By the way, I will also cover both MG logos with black ones.

 

[onkeldunkel]

I acutally like the Cyberster font/logo, but I will completely remove the back MG logo and maybe even the front one. I think they are way too big

 

[salty]

I personally would do the opposite. I would definitely leave the front and back MG logos, but would have them Black. And definitely lose the Cyberster badge.
But that's only my opinion of course.
Each to there own. And more importantly its your motor.

 

[m0rph]

Here:

• smaller black MG logo in front
• MG logo and cyberster logo delete in rear
• adding a black GT logo where cyberster logo was

I'll also play around with some black vinyl to fill the rear between the light, so I can hide the camera and trunk button. Something like this.

 

[onkeldunkel]

Yes there are few Cybersters in Thailand with that wrap. If someone can make an arrow that has flowing LED from the line into the arrow (dual direction)can do the same tint mod again. Then untint when youre bored if it... .But finding a light company to make that needs time and money

Next gen Cyberster should utilize the whole arrow with Audi style flowing signal. Or option it. Cheat codes for MG!

Great suggestions by everybody! I'ld like to add a few too:

I don't understand why you have to push the recline button of the chairs for +10s to make it go beyond a certain point. Wait 1s or beep if needed, but 10s is really a long time, and there's still plenty of space. Many test users might not know this and think the car is too small for anybody of average EU size.

Battery pre-conditioning(heating) when a charging station is set as destination, would be practical.

Is there a way to disable 'auto-creep' when putting the car in reverse?

In our Tesla Model X, the driver door closes when the driver pushes the brake pedal, it would be 'nice to have', it's certainly very practical.

Walk away auto-locking after some time.

Remember the last airconditioning setting and seat/steering wheel heating setting associated with top up vs top down and switch automatically with roof up/down.

Mobile app should deal better with the long latency for the round trip communication with the car.

Here:

• smaller black MG logo in front
• MG logo and cyberster logo delete in rear
• adding a black GT logo where cyberster logo was

I'll also play around with some black vinyl to fill the rear between the light, so I can hide the camera and trunk button. Something like this.

View attachment 34852

Looks nice - I really like it without the MG logo on the trunk. But looking at this, I will probably also remove the Cyberster logo to have a clean back (so no GT). I'm not a big fan of the blacked out area, but I'm considering to smoke the taillights to hide them a bit and maybe even black out the arrows like this one:

 

[m0rph]

Looks nice - I really like it without the MG logo on the trunk. But looking at this, I will probably also remove the Cyberster logo to have a clean back (so no GT). I'm not a big fan of the blacked out area, but I'm considering to smoke the taillights to hide them a bit and maybe even black out the arrows like this one:

I'm considering smoked headlights taillights too, and had them on my Tesla, but was pulled over by the Belgian police and had to remove them immediately..

 

[onkeldunkel]

I also had it on my Tesla and fortunately I was never pulled over

And I wrapped the calipers in reflective 3M wrap . It looks cool, so I might do that on the Cyberster too. I had a company do it on my old Model S, but on my Model X, I did it myself

 

[4Rens]

In other words, the longer we wait, the more (beautiful) accessories will come to the market.
I've already collected a few, now the Cyverster

 

[onkeldunkel]

I'm considering smoked headlights too, and had them on my Tesla, but was pulled over by the Belgian police and had to remove them immediately..

Oh, I misread - you said headligths . On my Model X it was the taillight I had smoked. On my Model S, I had a guy take the headlights apart and paint the inners black. It looked like smoked headlights, but leaving the actual glass part as-is.

 

[m0rph]

Oh, I misread - you said headligths . On my Model X it was the taillight I had smoked. On my Model S, I had a guy take the headlights apart and paint the inners black. It looked like smoked headlights, but leaving the actual glass part as-is.

Well, and I meant the tail lights anyway. LOL

 

[GranTurismoEra]

Looks nice - I really like it without the MG logo on the trunk. But looking at this, I will probably also remove the Cyberster logo to have a clean back (so no GT). I'm not a big fan of the blacked out area, but I'm considering to smoke the taillights to hide them a bit and maybe even black out the arrows like this one:

Debadge is ok. I saw on other forums its hit and miss. Unfortunately the indicators are in the arrow bit If you tint the arrow aka flag youll darken the indicators. LED should be ok with a slight tint though. The flowing style then split in both directions on the arrow bit is wishful thinking really. It would look cool though. Or just a line with flowing LED in the direction of the indicators. Then black out the arrow...Customize!